aku udah nyoba konfigurasi di router asli..
tapi masi pake yang konfigurasi router statis..
cuma sekedar berbagi ilmu aja…
Baru-baru ini aku baru belajar konfigurasi Router Dinamik di packet tracert menggunakan RIP versi 1 dan Versi 2
perbedaan RIP versi 1 dan RIP versi 2 adalah pada pemakaian host nya. jika menggunakan RIP versi 2 penggunaan host lebih efisien, karena host yang ada dipakai sesuai keperluan.
pertama bukalah software packet tracert
kemudian buatlah Rangkaian network seperti ini :
isi command line dari Router_1 :
RouterLampung#conf t
RouterLampung(config)#interface se0/0/0
RouterLampung(config-if)#ip address 10.2.0.0 255.255.255.0
RouterLampung(config-if)#clock rate 64000
RouterLampung(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
RouterLampung(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterLampung#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterLampung#conf t
Enter configuration commands, one per line. End with CNTL/Z.
RouterLampung(config)#interface fa
RouterLampung(config)#interface fas0/0
RouterLampung(config-if)#ip address 10.1.0.1 255.255.255.0
RouterLampung(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
RouterLampung(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterLampung#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterLampung#conf t
RouterLampung(config)#router rip
RouterLampung(config-router)#version 2
RouterLampung(config-router)#network 10.2.0.0
RouterLampung(config-router)#network 10.3.0.0
RouterLampung(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterLampung#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
isi command line Router_2
RouterJakarta (config)#interface se0/0/1
RouterJakarta(config-if)#ip address 10.3.0.2 255.255.255.0
RouterJakarta(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
RouterJakarta(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
RouterJakarta(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterJakarta#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterJakarta#conf t
Enter configuration commands, one per line. End with CNTL/Z.
RouterJakarta(config)#interface fa
RouterJakarta(config)#interface fastEthernet 0/0
RouterJakarta(config-if)#ip address 10.10.0.3 255.255.255.0
RouterJakarta(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
RouterJakarta(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterJakarta#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
Enter configuration commands, one per line. End with CNTL/Z.
RouterJakarta(config)#router rip
RouterJakarta(config-router)#version 2
RouterJakarta(config-router)#network 10.4.0.0
RouterJakarta(config-router)#network 10.10.0.3
RouterJakarta(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterJakarta#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
RouterPalemabeng(config)#interface serial 0/0/0
RouterPalemabeng(config-if)#ip address 10.2.0.2 255.255.255.0
RouterPalemabeng(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
RouterPalemabeng(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
RouterPalemabeng(config-if)#interface fa
RouterPalemabeng(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterPalemabeng#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
Enter configuration commands, one per line. End with CNTL/Z.
RouterPalemabeng(config)#interface fa
RouterPalemabeng(config)#interface fastEthernet 0/0
RouterPalemabeng(config-if)#ip address 10.1.0.1 255.255.255.0
RouterPalemabeng(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
RouterPalemabeng(config-if)#exit
RouterPalemabeng(config)#router rip
RouterPalemabe(config-router)#version 2
RouterPalemabe(config-router)#network 10.2.0.0
RouterPalemabe(config-router)#network 10.1.0.0
RouterPalemabe(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by console
RouterPalemabeng#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
